Interior Sets

Entry Handlesets

Deadbolts

Entry Sets

Cabinet Hardware

Accessories

Farmhouse Cabinet Pulls: Styles, Sizes, and How to Choose

Farmhouse Cabinet Pulls: Styles, Sizes, and How to Choose


The best farmhouse cabinet pulls are simple bar or cup pulls in matte black iron, sized by the distance between their screw holes. Most kitchen drawers take a 6" pull. Small drawers and vanities take a 4", and wide drawers and larger cabinet doors take an 8". To measure, check the center-to-center spacing between the two screw holes, not the overall length of the pull. Our Barn and Machine pulls come in all three sizes, cast iron and hand-finished, so they read as farmhouse without any decoration.

Black cast iron cup pull on a green painted farmhouse drawer under an oak countertop

Shown: Castle 4" Cabinet Cup Pull, the classic farmhouse alternative to a bar pull.

What Cabinet Pulls Work in a Farmhouse Kitchen?

Farmhouse pulls look made, not manufactured. That comes from a simple shape, real weight, and a matte finish that doesn’t throw back light. Ornate scrollwork and shiny chrome finishes detract from that understated, handcrafted character.

Shape sets the tone. The Barn pull with round corners is the most traditional option and sits easily on shaker and beadboard cabinets. The angled corner Barn pull leans industrial, a good accompaniment for open shelving, concrete, or reclaimed wood. The Machine pull has a square base and straight lines, which makes it the right call for modern farmhouse kitchens with flat-panel cabinets.

If you want something softer than a bar on drawers, the Castle cup pull is the classic farmhouse alternative. For how to pair pulls with knobs, see our rustic cabinet hardware guide.

Pick one pull style for the whole kitchen first, then decide where knobs go. Compare the shapes side by side in the cabinet pulls collection, or browse the full collection to see them next to our door hardware.

Material: Cast iron, hand-finished, zinc plated and powder coated matte black

Matte black cast iron bar pulls on a white shaker drawer and pair of cabinet doors

Shown: Barn Round pulls on white flat-panel drawers in a modern farmhouse kitchen

What Size Pull Fits Your Drawer?

Pull sizes are measured from the center of one screw hole to the center of the other. This measurement is included in every Barn and Machine pull name, so a 6" pull has screw holes spaced 6 inches apart.

To find the right pull size, start by measuring the width of your drawer front. A good rule of thumb is to choose a pull that’s about one-third the drawer’s width.

  • Drawers around 12" wide take a 4" pull.
  • Drawers around 18" wide take a 6" pull, a common size for most kitchen drawers.
  • Drawers 24" and wider take an 8" pull.

Farmhouse kitchens have a few spots that math doesn’t cover. A deep pot drawer under the range looks better with the 8" even when it runs a little narrow, because the drawer face is tall. Tall pantry doors take the 8" mounted vertically, and a standard upper door takes the 4".

Before you order, measure each drawer front, write the pull size on a strip of painter’s tape, and stick it on the drawer. Then count by size and shop the cabinet hardware collection.

Cabinet pull size guide showing 4, 6, and 8 inch pulls on 12, 18, and 24 inch farmhouse drawers

How Do You Measure for Cabinet Pulls?

Measure the holes, not the hardware. Remove one existing pull and measure from the center of one screw hole to the center of the other. If it reads 4, 6, or 8 inches, a Barn or Machine pull goes right into the old holes. No filling, no new drilling.

Diagram showing how to measure cabinet pull hole spacing center to center with a tape measure on a drawer front

If it reads 3-3/4" or 5", the old pulls were most likely metric (96 mm or 128 mm). Those won’t line up with an inch-sized pull, so plan to fill the old holes and drill new ones.

On new cabinets, center pulls on drawer fronts. On doors, mount them vertically on the side opposite the hinges, near the bottom corner on uppers and the top corner on base cabinets. Our pulls project about 1.2 inches, so check clearance at corner cabinets where two doors meet.

Every pull ships with short and long screws. Use the long set on thicker drawer fronts and doors.

Mark your hole spacing on a scrap of cardboard and use it as a drilling template on every drawer so the row lines up. Once the kitchen is done, carry the same black onto the interior door hardware, hinges, and switch plates. Plan it room by room in the full collection.

Frequently Asked Questions

What cabinet pulls work best in a farmhouse kitchen?

Simple bar or cup pulls in matte black with a textured surface work best. Round-corner bar pulls suit a traditional farmhouse, angled corners lean industrial, and straight-lined pulls suit modern farmhouse. Ornate or polished hardware works against the look.

What size pull fits an 18-inch drawer?

A 6" pull fits an 18-inch drawer. A pull about one-third the width of the drawer front looks proportioned, which puts a 12-inch drawer at 4" and a 24-inch drawer at 8". Pull size is measured center to center, between the screw holes.

How do you measure cabinet pulls?

Measure center to center, from the middle of one screw hole to the middle of the other. That number is the pull’s size, not its overall length. When replacing hardware, match the existing spacing so you don’t need new holes.

What if my old holes don’t measure 4, 6, or 8 inches?

Your old pulls were most likely metric, often 96 mm (about 3-3/4") or 128 mm (about 5"). Inch-sized pulls won’t line up with those holes. Fill and touch up the old holes, then drill new ones with a template so every drawer matches.

What is projection on a cabinet pull?

Projection is how far a pull stands out from the cabinet face. It decides how much room your fingers have and whether neighboring doors and drawers clear each other. The Barn and Machine pulls project about 1.2 inches, so check corner cabinets where two doors meet.

What’s the difference between the Barn and Machine pulls?

The difference is shape. The Barn pull is a simple bar with round or angled corners, and the Machine pull has a square base and straight lines. Both are cast iron, come in 4", 6", and 8", and project about 1.2 inches from the cabinet face.

Can I use the same pulls in a bathroom?

Yes. The Barn and Machine pulls are made for both kitchen and bathroom cabinets and drawers. Using the same pull in both rooms keeps the finish consistent through the house.

Build Your Matched Hardware System

From kitchen drawers to the front door, one cast iron finish in every room.

The Complete Black Iron Collection